当前位置:首页-新闻资讯

铝单板的施工准备注意七点

来源:http://www.jndclyyxgs.com/ 发布时间:2022-07-30

铝单板是适用于多种生活工作场所,如:写字楼、机场、地铁、轻轨、车站、展馆、医院、行政办公大楼,商业楼等各种场所,符合环保要求。那么铝单板的施工准备注意什么呢?
Aluminum veneer is suitable for a variety of living and working places, such as office buildings, airports, subways, light rails, stations, exhibition halls, hospitals, administrative office buildings, commercial buildings and other places, in line with environmental protection requirements. So what should be paid attention to in the construction preparation of aluminum veneer?
1、详细核查该施工图纸和现场实测尺寸,以确保深化设计加工的完善,同时认真与结构节点图进行核对,发现其不相符的部位,尽早修正设计。
1. Check the construction drawings and on-site measured dimensions in detail to ensure the perfection of deepening design and processing. At the same time, carefully check with the structural node drawing, and correct the design as soon as possible if it is found to be inconsistent.
2、检查横竖龙骨的质量是否符合图纸要求。横竖龙骨安装符合设计规范要求。横竖龙骨安装的连接螺栓不可漏装。为了保证板的安装精度,宜用经纬仪对横梁竖框杆件进行贯通,变形缝、沉降缝、变截面处等应妥善处理,使其满足使用要求。
2. Check whether the quality of horizontal and vertical keels meets the requirements of the drawing. The installation of horizontal and vertical keels shall meet the requirements of design specifications. The connecting bolts for horizontal and vertical keel installation shall not be omitted. In order to ensure the installation accuracy of the plate, it is advisable to use a theodolite to connect the beam and mullion members, and the deformation joints, settlement joints, and variable cross-sections should be properly handled to meet the use requirements.

铝板生产厂家
3、金属连接件材质及加工几何尺寸必须符合设计要求,材质必须有出厂合格证及复试报告。
3. The material and processing geometric dimensions of metal connectors must meet the design requirements, and the material must have factory certificate and retest report.
4、连接件与竖龙骨的连接要可靠,不要漏放弹垫。
4. The connection between the connector and the vertical keel should be reliable, and the spring pad should not be missed.
5、铝板生产厂家建议您对铝板材质、板面色泽、强度、外观、加工精度等进行检查,看是否符合设计及国家标准。
5. The aluminum plate manufacturer recommends that you check the aluminum plate material, surface color, strength, appearance, processing accuracy, etc. to see whether it meets the design and national standards.
(1)检查铝板的长宽尺寸偏差、对角线尺寸差、对边平行度偏差等加工精度:联合世纪铝单板的各项加工精度要求均按远高于国家标准的本企业标准执行。
(1) Check the processing accuracy of aluminum plate, such as length and width dimension deviation, diagonal dimension difference, and opposite side parallelism deviation: all processing accuracy requirements of Lianhe century aluminum veneer are implemented in accordance with the enterprise standard that is much higher than the national standard.
(2)检查铝板板面的平整度:板面平整用3M靠尺检查,允许偏差3Mm。板面垂直、水平用3M靠尺检查,允许偏差2.5mm,阴阳角用方尺检查,允许偏差2.5mm。
(2) Check the flatness of the aluminum plate surface: the flatness of the plate surface is checked with 3M guiding rule, and the allowable deviation is 3mm. The vertical and horizontal of the plate surface shall be checked with 3M guiding rule, and the allowable deviation is 2.5mm. The internal and external corners shall be checked with square rule, and the allowable deviation is 2.5mm.
(3)检查铝板的折边角度及多折形板的角度偏差:要在±0.50以内,铝板折边的圆角半径符合设计规定,折边一次成型。
(3) Check the folding angle of aluminum plate and the angle deviation of multi folded plate: it should be within ± 0.50, the fillet radius of aluminum plate folding should meet the design requirements, and the folding should be formed at one time.
(4)板折边上的铆接挂耳的位置正确。
(4) The riveting lug on the folded edge of the plate is in the correct position.
(5)所提供的加工成型板表面不得有明显压痕,印痕和凹陷等残迹,板面无损伤,无隐伤及斑纹。
(5) The surface of the processing and forming plate provided shall be free of obvious indentation, impression, depression and other residues, and the plate surface shall be free of damage, hidden injury and speckle.
(6)肋板与铝板背连接所用植钉,在植钉完成后铝板表面不应有明显凸起、凹陷和涂层表面不得产生影响观感的现象,固定牢固。
(6) The planting nails used for connecting the rib plate and the back of the aluminum plate shall be firmly fixed without obvious bulges, depressions and coating on the surface of the aluminum plate after the planting nails are completed.
(7)铝板应按设计图要求进行标记。
(7) The aluminum plate shall be marked according to the requirements of the design drawing.
6、板材进场,按规格编号堆放,防止碰撞及污染。
6. When entering the site, the plates shall be stacked according to the specification number to prevent collision and pollution.
安装施工前要搭设脚手架,安装操作的吊篮请有关部门进行验收。检查脚手架是否符合幕墙施工及规范要求。更多相关内容就来我们网站http://www.jndclyyxgs.com进行咨询了解吧。
Before installation and construction, scaffolds shall be erected, and the hanging baskets for installation and operation shall be checked and accepted by relevant departments. Check whether the scaffold meets the requirements of curtain wall construction and specifications. Come to our website for more relevant content http://www.jndclyyxgs.com Consult and understand.