铝板这些材料具有强烈的时代感和技术感，以及很高的艺术感染力。然而，铝板的使用还有一些需要注意的方面，那么在使用铝板时需要注意的事项是什么呢？铝板生产厂家为您讲解。
These materials of aluminum plate have a strong sense of the times and technology, as well as a high artistic appeal. However, there are still some aspects to be paid attention to when using aluminum plates. What are the matters to be paid attention to when using aluminum plates? The aluminum plate manufacturer will explain it to you.
1.铝板使用条件：内墙板应在室内使用，不应安装在室外，以保证使用效果和使用寿命。
1. Service conditions of aluminum plate: interior wall plate shall be used indoors, not installed outdoors, to ensure service effect and service life.
2.铝板安装方向：当同一色铝板安装在同一平面上时，流动方向应相同，否则可能造成视觉色差。
2. Aluminum plate installation direction: When aluminum plates with the same color are installed on the same plane, the flow direction should be the same, otherwise visual color difference may be caused.
3.铝板的撕裂膜：应在安装铝板后45天内将保护膜撕掉，否则可能发生撕膜或移动胶水的困难。
3. Tear film of aluminum plate: tear off the protective film within 45 days after installing the aluminum plate, otherwise it may be difficult to tear the film or move the glue.
4.铝板批次：同一型号和不同批次的钢板可能有色差，在销售和使用不同批次的中厚板时，应增加色差比较的程序。本公司主要经营铝合金铝板、铝板等，在不考虑色差的情况下只能在同一平面上使用。
4. Aluminum plate batch: steel plates of the same model and different batches may have color difference. When selling and using medium and thick plates of different batches, the procedure of color difference comparison shall be added. The company mainly deals in aluminum alloy aluminum plates, aluminum plates, etc., which can only be used on the same plane without considering the color difference.
5.铝板的贮存和运输：铝板应存放在干燥通风的地方，平放在平面上，不得踩踏和撞击，搬运板应同时抬起板的四面，严禁推、拉、拔，以免刮伤板表面。
5. Storage and transportation of aluminum plates.

6.铝板弯曲边的圆弧加工：弯曲边应均匀，一次成型，不要反复弯曲，否则铝板可能会断裂，加工电弧应采用特殊的弯曲设备，缓慢作用力，使板材逐渐达到要求的表面。不要一次弯曲。
6. Arc processing of bending edge of aluminum plate: The bending edge shall be uniform, formed at one time, and do not bend repeatedly, otherwise the aluminum plate may break. Special bending equipment shall be used for arc processing, and the force shall be applied slowly to make the plate gradually reach the required surface. Do not bend at once.
7.铝板开槽：当开槽机或锣机用于开槽时，应使用大于90度的半圆头铣刀。刀不应对铝板造成太深的伤害，也不应使边缘难以折叠。0-0.3mm厚的塑料芯应与铝板一起弯曲，以提高强度和韧性，否则铝板可能会断裂，或在边缘弯曲时油漆膜会破裂。
7. Aluminum plate slotting: When the slotting machine or gong machine is used for slotting, a semicircle head milling cutter greater than 90 degrees shall be used. The knife shall not cause too deep damage to the aluminum plate, nor make the edge difficult to fold. The 0-0.3mm thick plastic core shall be bent together with the aluminum plate to improve the strength and toughness, otherwise the aluminum plate may break, or the paint film may break when the edge is bent.
铝板表面使用中应注意的事项基础上就是这些内容了，您对此有什么想咨询的问题或者有需求吗？欢迎来我们网站http://www.jndclyyxgs.com进行咨询了解！
This is the basis for the precautions in the use of aluminum plate surface. Do you have any questions or needs? Welcome to our website http://www.jndclyyxgs.com Ask about it!