一、以便削减数控刀片和材料的滑动摩擦力,要求采用一些乳化油,在铝圆片出产加工进行后,残余在上边的光洁油没办法简易的擦拭除去,这就要求特别的除油剂去除,常见的方法有侵泡除油及其自喷除油。
1、 In order to reduce the sliding friction between the digital control blade and the material, it is required to use some emulsified oil. After the production and processing of the aluminum wafer, the residual cleaning oil on the upper side cannot be simply wiped off, which requires the removal of special degreaser. The common methods are foam oil removal and self spraying oil removal.
二、自喷除油、去灰:
2、 Self spraying oil and ash removal:
1、加适当的水分別稀释液除油剂和去灰剂;
1. Add appropriate water to separate Paint thinner degreaser and ash remover;
2、调理好喷头视角;
2. Adjust the perspective of the nozzle properly;
3、保证铝合金型材工艺品的自喷時间(许多于30秒);
3. Ensure the self spraying time of aluminum alloy profile handicrafts (many less than 30 seconds);
4、保证铝圆片有循环系统手洗。
4. Ensure that the aluminum discs have a circulation system for hand washing.
三、侵泡除油、去灰:
3、 Immersion and degreasing, ash removal:
1、在使用前加小量的饮用水,随后将铝圆片机加工件渗入池中;(调理好去灰剂);
1. Add a small amount of drinking water before use, and then infiltrate the aluminum wafer machined parts into the pool; (Adjust the ash remover properly);
2、参加铝圆片除油剂,在5--10秒内全自动发烫;
2. Participated in aluminum wafer degreasing agent, fully automatic scalding within 5-10 seconds;
3、2~3分鐘除油终结,用饮用水整理;
3. After 2-3 minutes of oil removal, clean with drinking water;
4、进到去灰剂中来灰(時间不跨越30秒左右);
4. Enter the ash remover to remove ash (time does not exceed about 30 seconds);
5、饮用水整理------风干(暴晒)或是停止空气氧化。
5. Drinking water treatment - air drying (exposure to sunlight) or stopping air oxidation.
铝圆片的清理流程:
Cleaning process for aluminum wafers:
1、先用许多的冷水清洗铝圆片外表有尘垢,随后在上边洒经水稀释液过的洗涤剂,用薄布擦拭铝圆片的外表,然后用许多的冷水清洗方才清洗后的外表,将铝圆片外表的脏物都冲跑。
1. First, use a lot of cold water to clean the surface of the aluminum wafer, and then sprinkle the detergent with water Paint thinner on it, wipe the surface of the aluminum wafer with a thin cloth, and then use a lot of cold water to clean the surface of the aluminum wafer after cleaning, and flush away the dirt on the surface of the aluminum wafer.
2、查验铝圆片的外表,看一下有没有没清洁,有关沒有洗洁净的在停止重中之重整理,知道一切洗洁净才行,随后用冷水将洗濯剂一切冲走。
2. Check the appearance of the aluminum wafer to see if it is clean. For those that have not been cleaned, it is important to stop sorting and ensure that everything is clean. Then, rinse off all the detergent with cold water.
3、此外要注意的是不用整理温度比较高的铝圆片,由于水份过快的蒸腾就会对外表的喷漆危害,使用洗濯剂的时段,一定要选择中性化的洗濯剂,不然将会浸蚀铝圆片的外表。
3. In addition, it should be noted that there is no need to organize aluminum wafers with high temperatures. Due to the rapid evaporation of water, it can cause damage to the surface of the spray paint. When using cleaning agents, it is necessary to choose a neutral cleaning agent, otherwise it will corrode the surface of the aluminum wafers.
This article is a friendly contribution from aluminum coil manufacturers. For more information, please click on: http://www.jndclyyxgs.com Sincere attitude. We will provide you with comprehensive services. We will gradually contribute more relevant knowledge to everyone. Stay tuned